ריבוע תיתורא
Is it מעכב if the תיתורא תחתונה doesn't meat up with the עליונה
How is it fixed?
How about the Bais of Uleovdo?
Popular posts from this blog
Ink, Kosher vs. non-Kosher
We all know that there is no ancient source that requires ink to be מן המותר בפיך . Possibly, as said here before, because in the olden days ink was always מן המותר בפיך and the question was never raised. It was probably self-evident. Nowadays, no decent Rav will approve an ink which is not מן המותר בפיך . Who was the first one to raise this question? Was it raised because of animal ingredients or because of non-kosher wine?
Question to Yosef Chaim B
Thank you for commenting on my ink article. In your comment you stated: "Many poskim disagree... Many rishonim have clearly stated the use of our ingredients." Would you please be kind enough to teach us (so I can include it in the article) which Poskim and what exactly and where did they say that the עפצים וקנקנתום type of ink is preferable over good quality דיו עשן that does not fail? We are not interested in biased פילפולים , or in those who said that דיו עשן is not being used because it fails easily or because it was not known how to make good quality דיו עשן. Nor are we interested in those who said to use עפצים וקנקנתום וגומא ואין לשנות when they discussed specifically the עפצים וקנקנתום type of ink. We are interested to find out where and who (if any) said explicitly, based on sources, that the עפצים וקנקנתום type of ink is preferable over good quality דיו עשן , even when there is דיו עשן of good quality that does not ...
I'm not sure of the name but I use this type of clamp http://www.google.com.au/search?q=clamp&safe=off&hl=en&prmd=ivnsp&source=lnms&tbm=isch&sa=X&ved=0CAYQ_AUoAWoVChMIpNjKnrm8xwIVYtumCh2GggSA#mhpiv=13
ReplyDeleteOne side does on the bottom back of the mabarta, the other on the front upper titura and it pushes it back in place so titurah elyona and tachtonah will be flush. You can even use it while you sew, and overcompensate on the other direction so when you release the clamp it will be perfectly centred.
A gutte Voch
the type of clamp is called a Bar Clamp. The link above isn't good, please google "bar clamp".
DeleteA clamp, even after sewing, will likely not make the upper and lower titura permanently flush. You'll most likely need to glue it once you get it lined up. If it's still off then you'd fix it by sanding. One who is experienced with batim work can easily handle this. As is, it shouldn't be used.
ReplyDeleteI don't think you understand the type of clamp I refer to. The link was bad, it's called a Bar Clamp, you overcompensate so that the mabarta is pushed so hard the non extended part of the titura sticks out (well) past the more extended side . If you do it for too long or too hard you may end up reversing which side of the ttitura sticks out more. I find this often works even without glue or shaving afterwards.
ReplyDeletePlease excuse my ignorance: what is the Halachik problem with this? If each part is "rabua" why must they meet?
ReplyDeleteI am wondering about the Halacha. Not aesthetics or practical. Just Halacha.
Thank you Eli, I'll just give it to a batim macher.
ReplyDeleteYY I was wondering the same thing but in zichron Eliyahu he says it's a problem according to some reshonim. BTW according to a''r the titura elyona is part of bayis as he says to sowe the titura with the bayis. Correct me if I'm wrong
Thank you Heshy.
ReplyDeleteI've been using a clamp (I'll provide an image in a new post as I don't know how to add an image to a comment) for years and it's widely popular among those who work with batim. On one side it has a perfect indentation into which the edge of the titura fits enabling one to adjust the titura. However, even after overcompensating, the titura will often slide back more than to the correct position again leaving a "lip" or "step", hence, gluing it in place once you have it in the desired position is strongly recommended.
ReplyDeleteI have a number of bar clamps as well. The ends are soft and it works well when I add a little glue between the bayis shel rosh at the bottom because it doesn't affect the paint on the Shins. I only slightly tighten it slightly so as not to affect the finish of the Shins and so the glue doesn't go too high.